SERIES 6.1

Přímý modulární pás I Rozteč modulů 50 mm (1.97 in)

Pro středně těžké až těžké aplikace náročné na hygienu

Design characteristics

  • Wide modules and eyelets for less soiling

  • Hinges that open wide, wide channels on the underside
    and a continuous drive bar for an easy-to-clean design

  • robust design and smooth, cut-resistant surface (depending on material)

  • Special sprocket design with enhanced tooth engagement
    for excellent force transmission

Basic data

 

Pitch

 

Belt width

min.

Width

increments

 

Hinge pins

 

50 mm (1.97 in)

 

40 mm (1.57 in)

 

20 mm (0.8)

Made of plastic (PE, PP, POM-MD, PBT)

S6.1-0 FLT | 0 % Opening | Flat top

 

  • Closed, smooth surface

  • Flat top surface

  • Easy-to-clean

S6.1-0 NTP | 0 % Opening | Nub top (round studs)

 

  • Closed surface and round studs

  • 6 % contact area

  • Nub top surface for good release of wet and sticky products

  • Easy-to-clean

S6.1-0 CTP

 

  • Closed surface and pointed studs

  • Cone top surface pattern for superior grip

  • Easy-to-clean

S6.1-21 FLT | 21 % Opening | Flat top

 

  • Open area (21 %) for excellent air circulation and drainage

  • 58 % contact area (Largest opening: 1.9 x 11 mm/0.07 x 0.43 in

  • Smooth surface

  • Easy-to-clean

S6.1-23 FLT | 23 % Opening | Flat top

 

  • Open area (23 %) for excellent air circulation and drainage

  • 61 % contact area (Largest opening: 4.3 x 9.3 mm/0.17 x 0.37 in)

  • Smooth surface

  • Easy-to-clean

S6.1-36 FLT | 36 % Opening | Flat top

 

  • Open area (36 %) for excellent air circulation and drainage

  • 20 % contact area (Largest opening: 11.8 x 15.2 mm/0.46 x 0.6 in)

  • Smooth surface

  • Easy-to-clean

Sprockets

 

In different sizes with round or square sprocket bore

Profiles

 

In different heights and designs for inclines

Side guards

 

In different heights for retention of bulk products

Hold Down Tabs

 

Hold Down Tabs for additional guiding

Pin Retained Rollers

 

For applications where low back pressure accumulation or product separation is required

TP ikona WT.PNG

Conveyor belts

MB ikona WT.PNG

Modular belts

OŘ_ikona_WT.PNG

Timing belts

PŘ_ikona_WT.PNG

Flat belts

Máte-li zájem o více informací o našich produktech, jejich výrobních procesech a materiálech, tak nás neváhejte oslovit již dnes a zjistěte, jak Vám můžeme pomoci.

     +420 381 521 162          info@mbelt.cz 

Sídlo společnosti:

M belt s.r.o.

Mánesova 345/13

370 01 České Budějovice

info@mbelt.cz

www.mbelt.cz

www.dopravnipasy.eu

Provozovna:

M belt s.r.o.

Na Ohradě 368

392 01 Soběslav

Tel.: +420 381 521 162

Fax: +420 381 521 162

info@mbelt.cz

www.mbelt.cz

  • Facebook - Bílý kruh

M belt s.r.o. - movement technologies solutions

Copyright © 1990 - 2021 M belt s.r.o.