top of page

SERIES 5

Zatáčkový a spirálový pás I Rozteč modulů 25 mm (0.98 in)

Design characteristics

​

  • Suitable for both straight and radius conveying

  • up to 45 % open area for excellent air circulation
    and drainage

  • Stainless steel hinge pins for high load capacity,
    lateral stiffness, fewer belt supports and minimum belt lifting in curves

  • No potential belt edge catch points due to safe fixing of hinge pins

Series_5.jpg

Basic data

 

Pitch

 

Belt width

min.

​

Width

increments

 

Hinge pins

​

 

25 mm (0.98 in)

 

100 mm (3.9 in), 175 mm (6.9 in) for S5 ST

​

25 mm (0.98)

​

​

Stainless steel

Basic Data Series 5.jpg

S5-45 GRT | 45 % Opening | Grid top

 

  • Open area (45 %) for excellent air circulation and drainage

  • Lattice shaped surface

S5-45 GRT.jpg

S5-45 NTP | 45 % Opening | Nub top (round studs)

 

  • Open area (45 %) for excellent air circulation and drainage

  • Lattice shaped surface with 3.0 mm (0.12 in) high round studs and 8 % contact area

  • Side modules without NTP-surface

S5-45 NTP.jpg

S5-39 FRT1

 

  • Excellent air circulation and drainage

  • Integrated friction pads (raised) increase surface friction and provide gentle grip

  • Side modules without FRT-surface

S5-39 FRT1.jpg

S5-33 FRT2 | 33 % Opening | Friction top (Design 2)

 

  • Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage

  • Integrated friction pads (flat) provide gentle grip

S5-33 FRT2.jpg

S5-45 GRT G | 45 % Opening | Grid top · guided

 

  • Excellent air circulation and drainage

  • Lattice shaped surface and Hold Down tabs

  • Allows utilisation of the entire belt width

S5-45 GRT G.jpg

S5-45 NTP G | 45 % Opening | Nub top (round studs) · guided

 

  • Excellent air circulation and drainage

  • With round studs for increased grip (8 % contact area)

  • Allows utilisation of the entire belt width

  • Side modules only available without NTP-pattern

S5-45 NTP G.jpg

S5-39 FRT1 G | 39 % Opening | Friction top (Design 1)

 

  • Excellent air circulation and drainage

  • Integrated friction pads (raised) increase surface friction and provide gentle grip

  • Allows utilisation of the entire belt width

  • Side modules without FRT-surface

S5-39 FRT1 RG.jpg

S5-33 FRT2 G | 33 % Opening | Friction top (Design 2)

 

  • Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage

  • Integrated friction pads (flat) provide gentle grip

  • Allows utilisation of the entire belt width

  • Side modules without FRT-surface

S5-33 FRT2 G.jpg

S5-45 GRT RG | 45 % Opening | Grid top · reversed guided

 

  • Excellent air circulation and drainage

  • Lattice shaped surface and reversed Hold Down tabs

  • Allows utilisation of the entire belt width

S5-45 GRT RG.jpg

S5-45 NTP RG | 45 % Opening | Nub top (round studs) · reversed guided

 

  • Excellent air circulation and drainage

  • With round studs for increased grip (8 % contact area)

  • Allows utilisation of the entire belt width

  • Side modules only available without NTP-pattern

S5-45 NTP RG.jpg

S5-45 NTP RG | 45 % Opening | Nub top (round studs) · reversed guided

 

  • Excellent air circulation and drainage

  • With round studs for increased grip (8 % contact area)

  • Allows utilisation of the entire belt width

  • Side modules only available without NTP-pattern

S5-45 NTP RG.jpg

S5-45 NTP RG | 45 % Opening | Nub top (round studs) · reversed guided

 

  • Excellent air circulation and drainage

  • With round studs for increased grip (8 % contact area)

  • Allows utilisation of the entire belt width

  • Side modules only available without NTP-pattern

S5-45 NTP RG.jpg

S5-39 FRT1 RG | 39 % Opening | Friction top (Design 1)

 

  • Excellent air circulation and drainage

  • Integrated friction pads (raised) increase surface friction and provide gentle grip

  • Allows utilisation of the entire belt width

  • Side modules without FRT-surface

S5-39 FRT1 RG.jpg

S5-33 FRT2 RG | 33 % Opening | Friction top (Design 2)

 

  • Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage

  • Integrated friction pads (flat) provide gentle grip

  • Allows utilisation of the entire belt width

  • Side modules without FRT-surface

S5-33 FRT2 RG.jpg

S5-45 GRT ST | 45 % Opening | Grid top · strong

 

  • Excellent air circulation and drainage

  • Lattice shaped surface

  • Version with reinforced brick-laid side modules (75 mm/2.9 in and 100 mm/3.9 in) increases belt pull capacity

S5-45 GRT ST.jpg

S5-45 NTP ST | 45 % Opening | Nub top (round studs) · strong

 

  • Excellent air circulation and drainage

  • With round studs for increased grip (8 % contact area)

  • Version with reinforced brick-laid side modules increases belt pull capacity

  • Side modules only available without NTP-pattern

S5-45 NTP ST.jpg

S5-39 FRT1 ST | 39 % Opening | Friction top (Design 1)

 

  • Excellent air circulation and drainage

  • Integrated friction pads (raised) increase surface friction and provide gentle grip

  • Reinforced side modules increase belt pull capacity

  • Side modules without FRT-surface

S5-39 FRT1 ST.jpg

S5-33 FRT2 ST | 33 % Opening | Friction top (Design 2) · strong

 

  • Open area (33 % for full FRT2 surface area) for excellent air circulation and drainage

  • Lattice shaped surface

  • Version with reinforced brick-laid side modules increases belt pull capacity

S5-33 FRT2 ST.jpg

Sprockets

 

In different sizes with round or square sprocket bore

s5_sprocket.jpg

Profiles

 

In different heights and designs for inclines

s5_profile.jpg

Side guards

 

In different heights for retention of bulk products

s5_sideguard.jpg

Ball-bearing modules

 

to minimize friction forces at the belt edge

s5_bearing.jpg
bottom of page